by Eight Bits

Rossi Ranch Hand 44 Magnum For Sale
Rossi Ranch Hand Manual Typewriters

Following are the steps I performed on my two Rossi's to slick them up and improve functioning. I am not a professional gunsmith, just a shooting enthusiast and hobbyist, as well as a tinkerer. If you are unsure aboutany of the following procedures, please defer to a qualified gunsmith. For polishing I use wet/dry 600 grit emery paper wetted with Hoppe's gun oil. To remove metal I use a jeweler's file, then polish as above. For stoning I use a hard Arkansas stone. To polish pivot pins I use oiled 600 grit emery paper, or oiled automotive crocus cloth. Work slowly and carefully and check functioning frequently. It's always easy to remove a little more metal, but adding metal is very difficult. As we learn, we may have to replace a part of two that we over work. That's part of the risk of the adventure.
Aways, wear safety glasses while working with springs or sanding.

Available - Excellent condition Rossi Lever Action hand gun known as the Ranch Hand. Packing a serious punch chambered in.45 L for sale by Valley Gun Works on GunsAmerica - 978310469. Bill good luck with your Rossi 92 the rule #20 probably applies to the Rossi Model 92 Ranch Hand model with the cut down barrel & stock to make it more a pistol vs the rifle aspect. Enjoy your Rossi 92 very fun little rifles! I want another in stainless steel or the blued case harden model. Rossi Ranch Hand Pistol Unleaded Ink. Arizona –-(Ammoland.com)- Most of us grew up on classic westerns and a few of us are old enough remember a black-and- white TV show that aired from 1958. R92 357 Mag 24' 12 Rounds Octagonal Barrel Stainless Steel / Brazilian Hardwood.

Disassemble the rifle and thoroughly clean all parts

Trigger Assembly
____1. Polish sides of trigger
____2. Polish trigger spring and trigger mating surface
____3. Lighten trigger spring by bending up
____4. Stone/polish hammer mating surfaces inside the lower tang
____5. Polish trigger pivot pin

Hammer Assembly
____1. Polish hammer strut
____2. Polish hammer sides where they contact the lower tang
____3. Polish hammer face
____4. Remove 4-6 coils from mainspring and flatten end
____5. Polish hammer pivot pin

Carrier
____1. If the carrier is too tight in the receiver, remove some metal from the right side of the carrier.
____2. Polish both sides of the carrier at the pivot pin holes

Ejector Assembly
____1. Remove all burrs
____2. Polish shaft
____3. Polish all mating surfaces
____4. Replace the ejector spring Spring from Stevesguns.com or Lee Spring Kit from Brownells or Lee Spring Kit from Lee's Gunsmithing
(NOTE: When reassembling the bolt the ejector will lie flat with the bolt face.
This is alright because once the finger lever is in place the ejector spring will be under tension.)
____5. Polish collar ends

Finger Lever
____1. Polish ejector collar camming surface
____2. Polish lever retaining pin (only if necessary).
(NOTE: This is the pin in the rear of the finger lever that sits in a detent in the receiver
and holds the lever closed.)
____3. Polish front and camming surfaces of bolt locks

Loading Gate
Sometimes the loading gate is too long and the cartridge rims get stuck on the sharp end of the gate.
____1. Use a stone to remove just enough metal off the end, and maintain the same contour
The end of the loading gate sits almost flush - just a bit inside the loading gate opening.
(NOTE: This important to ensure the last round loaded into a full magazine will feed properly.)
____2. Make sure the sides of the gate move freely in the opening.
If not, I run the edges of the loading gate over my stone a couple of times and try for fit.
(If you remove too much metal the gate will pop out of the opening.) I also polish the .
____3. Polish little ramp on the underside of the gate (only if necessary)
This helps the cartridge to be positioned correctly for loading on the carrier.
The secret - make a few strokes on the stone, then try for fit.
The goal - get the gate to fit in the opening almost flush without sticking out.

Bolt Assembly
____1. Polish hammer camming surface on the rear of the firing pin
____2. Polish hammer camming surface underneath rear of bolt
____3. Remove burrs and loose metal
____4. Polish sides and rails
____5. Ensure ejector rides smoothly in ejector cutout
____6. Polish front of bolt lock camming surfaces
____7. If extractor is too stiff when the bolt closes without a case, remove metal from the REAR
of the extractor until there is still a small amount of tension on the extractor.

Receiver
____1. Remove burrs and polish bolt rails. Try bolt in receiver to test for free travel.
Stone and polish any high spots

When reassembling the rifle, be sure all parts are lightly lubricated. Too much oil attracts dirt, too little oil causes excessive wear and friction.

Eight Bits

Note: Resist any temptation to polish either the locking bolts or the channels they rid in. These control the headspace of the rifle and should only be altered by a qualified gunsmith.

As an alternative to modifying the original springs that came with the rifle, it is common to install an aftermarket spring kit that provides the appropriate tension for a smooth operating Rossi 92. The Lee Spring kit comes with a replacement ejector spring that is much longer than the original. See the trick for installing the bolt into the rifle with an long and weak ejector spring. Rossi Assembly/Disassembly

And J.P. Withers notes from the SASS Wire:

Rossi 92 'Puma' - Lessons learned
byJ.P. Withers, SASS 68019

Hopefully I'm not re-inventing the wheel here but I thought I'd pass along some experience gained from working on the like-new Rossi “Puma”copy of the WInchester 92 SRC I picked up a while back. This carbine is chambered for .38 special/.357 magnum.

First, Marauder's webpage is a great resource. Marauder's Rifle Page But you probably already found that since you are here.

Make sure you pin the hammer spring before attempting to remove the hammer screw. If you don't do this you can still get the screw out but you will bung-up the threads (embarrassed shrug).

As others have said, the magic word for this rifle is 'SPRINGS'! I would never have believed how great the impact of the ejector spring is to the overall functioning of this rifle. I thought the hammer spring would have a big impact but was very surprised about the ejector spring.

The original (heavy) ejector spring made the rifle pull, chamber, and eject everything I fed it (including some step nosed LSWC rounds) but made the lever action so heavy I had to put a leather wrap on the lever to keep from bruising the back of my index finger. Looking at the rifle you'd think the resistance was coming from the locking bolts.. it doesn't, it's totally the ejector spring inside the bolt.

(Safety tip, DO NOT MESS WITH THE LOCKING BOLTS they set the headspace for the rifle)

Torrent official site. A weak (just slightly too weak for my gun, actually) aftermarket ejector spring made the rifle cycle as slickly as you can imagine, BUT it also caused my particular rifle to have trouble cycling the longer .357 rounds and also have random trouble ejecting any type of rounds.

I don't personally recommend this, but if you intend to try the 'cut and expand' method on your springs (see Bull Schmitt's instructions about 1/2 way down the page here..) Bull Schmitt's Instructions then have extra ejector springs handy -BEFORE- you start experimenting or you'll sit idle for a while - while you get new ones. WEAR SAFETY GLASSES when working with springs! (The shortened springs don't hold up for most folks.)

The original hammer spring is too damn heavy. Don't bother messing with it, just buy a replacement at Brownells. (But shortened springs can work, if you prefer.)

If you feel the need to remove the cartridge guides, inspect the left one (with the swivel on it) carefully before re-installing. If the swivel pin drops down even a tiny bit

Rossi Ranch Hand Manual